Home | Tournaments | Calendar | Weather | Merchandise | Sponsors |
|
All About Guns What's your weapon of choice, and why? Discuss the beloved speargun here! |
|
Thread Tools | Rate Thread | Display Modes |
04-16-2018, 11:59 AM | #61 |
The Ocean is Calling
Join Date: Mar 2011
Location: Jupiter, FL
Posts: 349
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
There is definitely wear on the back roller. I am not sure if it is from regular use or from the time I tried to load it when the roller was skewed. Like I said i noticed it didn't load and tried maybe once a little harder to load before I realized it may have skewed like others had mentioned. I took the trigger out of the gun to inspect the parts and The front roller didnt spin as easily after all those hot banded shots either. The back roller has several marks in it. There are more than could have been made from the rear roller skewing one time. There is a possibility it was slightly skewed on other loading sequences and I just didn't notice any difficulty. All other times the shaft engaged in the trigger quite easily.
Still have high hopes. It seemed great until the pressure from hot bands. Last edited by SEA_ARCHER; 04-16-2018 at 12:40 PM. |
04-17-2018, 12:55 AM | #62 |
Registered User
Join Date: May 2009
Posts: 3,292
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Hmmm ... that is not good. Thanks for the feedback! I have to admit that I had my doubts about the floating roller working well once loaded up .... I mean it is rotating off axis and it is really difficult to predict how that affects rotation. But Mario said he was using that trigger on a modified double roller box with 3 bands with no problems. The thing is that it is really difficult to know if the front roller is rotating or if it is not. If it is not, then this just works like a friction trigger and thus is vulnerable to scratching or galling. You will get a few good shots, but once the scratches start happening the break off point will not be predictable ... and that means accuracy goes down hill. Even if the break is identical each shot, but the break is in different locations of the trigger pull ... the accuracy will drop dramatically. I can see that when testing on a target in the pool. The shots start "walking" off target as the trigger gets scratched.
As for the back roller scratches, it looks like this is just 316 roller and not 17-4 hardened ... this of course should be changed to 17-4 as this is much harder and will resist hard shafts better. But to be honest the scratches on the back roller will not affect performance, so I wouldn't worry about that. More important is dealing with the front roller and making sure that it turns properly and predictably. I do have a drawing for a mini 6.6 roller sear similar to the double roller, but this would need to be CNC cut (expensive). The roller on that would be about 20% smaller than what is on the double roller ... but for 2 hot bands such as the Pathos 130 ... it should be plenty strong enough. I couldn't get Mario interested in that trigger as it just costs too much to make and he doesn't think it would sell. I might make a few of those sears just to try out the idea. Another possibility is just to use a .25" plate to cut the sears ... this comes out to be about 6.35mm ... and you could laser cut the sear and then you just need one CNC front cut for the front roller. But at 6.35mm the roller would be a little smaller than at 6.6 ... but by using a hardened trigger sear it should be more than strong enough. I think C4 uses a very small front roller and it seems to work ok. At least the double roller system is well tested and there are several thousand of those triggers in use today ... so we know it works well. |
04-17-2018, 01:53 AM | #63 |
Shooter & Shooter
Join Date: Nov 2014
Posts: 955
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
I don't want to sound the least bit know-it-all'ish but when I saw the front cradle design I have to admit, I was slightly confused. The thing that caught my eye was that the area of contact is so much bigger at the roller to cradle point than it is from roller to trigger. In my thinking, that could lead to a lot of friction, which could possibly be what is happening here.
I am with Majd, that it makes sense to try to make that roller sit "properly" on a pin, instead. Either way, I hope and trust Mario will get it right:-) Majd, a manufacturing question: I understand the need for a second operation to cut a vertical slot in the sear for a roller to sit in with a pin. But is there any reason you can't do this on the laser, too? Couldn't you take the cut out sears, turn them 90 degrees and place them in a jig for that second cut-out or will the heat potentially warp the part and throw it off tolerances? I know the fixture would have to be manufactured, too and possibly on CNC, but that's a one time expense. Last edited by Diving Gecko; 04-17-2018 at 02:38 AM. |
04-18-2018, 01:28 AM | #64 | |
Registered User
Join Date: May 2009
Posts: 3,292
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
To cut many parts out of a single laser pass can be done very very quickly and efficiently. To take an individual part and put it on a custom jig and check that tolerances are extremely high and only then do the CNC cut ... well it is very time consuming and not easy to automate. You reach a point where it is just as expensive to cut the entire sear via CNC. I think this could easily be automated using Swiss Screw CNC machines as these machines are programmable lathes that can also do horizontal cuts ... but for some reason all the shops that have these machines just use the extra efficiency to make more profit, and prices are also high. It all boils down to cost. Will someone pay an extra $15 or $20 for a trigger? I certainly would and probably several people in this forum that understand the problems also would. But I can tell you that I have had discussions with trigger designers from major spearfishing companies and they still have no clue that the galling in triggers can cause a huge drop in accuracy. They figure so long the trigger shoots it should be fine. Of course there is always the alternate system I mentioned earlier ... that really will transform how all triggers are made and do it much cheaper. But my guess is that without a patent this would easily be copied. Mario still thinks the front roller system will work well and just yesterday he sent me the latest drawings and I put them on a computer and simulated the action. According to the simulation the back roller problem is fixed, but there is no real good way to simulate the rotation of the front roller as it is off center and not on an axis. Even if there was proper data for that, I would not feel comfortable with it unless it was tested in real firing conditions with at least 500 shots. In the pool it is very easy to verify if the trigger is not shooting accurately as the shot groupings will tend to move around ... plus I have shot so many shots that I can feel the trigger pull is different. The floating front roller can still possibly work well even at high loads, but IMHO this has to be proven in testing before it becomes something that is sold to the public. |
|
04-18-2018, 02:27 AM | #65 | |
Shooter & Shooter
Join Date: Nov 2014
Posts: 955
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
Come to think about it, often big production runs actually prefer to use a second, or third, machine for subsequent operations. I had this chat with an engineering friend of mine who had 5 axis CNC mills at her disposal for their very 3D intensive machining. But they would rather run the parts on two or three 3 axis machines. Just move the parts from one machine, flip them over onto the fixtures in the next and so forth. But either way, I can see how that becomes expensive on small parts without much room for profit. No need to entertain my speculations any further, I was just curious and thanks again:-) |
|
04-19-2018, 12:09 AM | #66 | |
Registered User
Join Date: May 2009
Posts: 3,292
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
On my computer I can quickly put together a perfect trigger ... the challenge for Mario is not to have the perfect design, but rather to manufacture that design where it becomes cost effective to the end user ... that is the big challenge. |
|
05-10-2018, 02:30 PM | #67 |
Registered User
Join Date: Dec 2016
Location: Burleigh Heads, QLD, Australia
Posts: 39
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
I received a replacement mech today that has the front reinforcement, spring return line release, resolved rear roller skew issue and the wider front cradle roller.
The shaft aligns and loads perfectly, every issue resolved...except the front roller not rolling. 125 band stretch with 2 x 14mm @ 370% the trigger pull is still 3-4 times what is normal. I could handle a heavier trigger pull if it was smooth, but there is no give or feel to it until enough (unkown) force is amassed and of it goes. Don't really feel this is usable. |
05-10-2018, 03:13 PM | #68 | |
Registered User
Join Date: Aug 2010
Posts: 689
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
That’s really crazy. 2 mechs you’ve received and both giving you gripe. The one i just put into my Denton is flawless and definitely the smoothest crispest trigger mech I’ve ever used. An absolute pleasure to use. Sent from my iPhone using Tapatalk
__________________
www.cristspears.com |
|
05-13-2018, 12:26 AM | #69 | |
Registered User
Join Date: May 2009
Posts: 3,292
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
Sounds like the front roller is just locking and the trigger is just working as a friction trigger. I had the same issue, so obviously this is not a one off situation. I tend to have my band loads pretty high and maybe that exposes the problem better. Mario had redesigned the front end completely, and has put cut out guides for the front roller to make sure it rotates. Again I think this new setup also needs to be tested to be sure it works well. The problem with the Pathos trigger is that you just have 7mm of real estate to make your trigger. If you go the normal double roller route, with a roller rotating on an axle, you have very little space to put 2 arms holding the roller. I do think it is workable ... maybe using Nitronic 50 or 60 which is twice as strong as 316 SS ... but also 2.5x more expensive. |
|
05-13-2018, 01:02 AM | #70 | |
Registered User
Join Date: Dec 2016
Location: Burleigh Heads, QLD, Australia
Posts: 39
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
Moving forward, I would love to see Mario either redesign the trigger sear to match the geometry of his existing booster kit (which is nice) and settle for a single roller, which in my opinion would still be a significant improvement on the Ermes booster/Pathos set up. or... try cutting a 3mm slot in the 6mm trigger sear, to form arms, and running a 2.6mm wide roller within them. Its a very narrow roller I know, but could it be wide enough? I dont know. Im not really sure how much force there is acting on those two surfaces, how the trigger pull would feel with such a narrow roller or how long it would last. Should also be using the highest grade/quality materials...people buying this mech are doing so for the highest performance gains available and will understand the added cost. Its only a matter of time until other manufacturers jump on the band wagon and produce a fully functional double roller handle/gun. I see Salvimar is halfway there already (albeit the wrong half IMO) with the mech they are using on their Hero gun. They have a trigger roller but a standard friction shaft/sear arrangement. I Would like to see Mario get a DR drop in, that you don't have to build a whole gun around first...since he's done the hard yards to get it there. Last edited by NPG-70; 05-13-2018 at 01:12 AM. Reason: Added bits |
|
05-13-2018, 01:30 AM | #71 |
Registered User
Join Date: Dec 2016
Location: Burleigh Heads, QLD, Australia
Posts: 39
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Salvimar Hero Mech
|
05-13-2018, 01:43 AM | #72 | |
Registered User
Join Date: Aug 2016
Posts: 460
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
I think you are right about the front roller not rotating. I have not experienced a big problem here but maybe that’s because I use the trigger in a 95 Pathos Sniper roller and the forces on the spear are not high enough to accentuate the problem. In my case it might be working as a friction trigger but I still find it an improvement over the original one. I haven’t asked Mario for a replacement since the problem isn’t solved yet. Leaving for a spearfishing trip next week. I am going to put the trigger true it’s paces and see how it holds up over time. Sent from my iPhone using Tapatalk |
|
05-13-2018, 01:55 AM | #73 | |
Registered User
Join Date: May 2009
Posts: 3,292
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
I have managed to get a roller size of 3.9mm on the computer ... I think that is the absolute max for 7mm. Of course this is using a CNC milled 6.6mm sear (which is not cut from a standard sized plate). The Salvimar has much more real estate as it is wide all the way to the bottom (probably like 10mm). I have no idea why Pathos go the 7mm then expand to 10mm as I think the handle would be plenty strong even if they went 10mm wide. On the D'Angelo 1 handle it is around 14mm if you remove the trigger ... that would easily fit even a full bore double roller ... maybe need to shave off .5mm. I also think the D'Angelo 1 is a better handle shape. There will be a fully robust and perfectly working trigger for the Pathos D'Angelo 2 handle from Ermessub ... this I guarantee 100%. It just might take a month or two to get it in the pipe line. I have tested one of those triggers and it is a complete game changer. It is incredible how much a good, crisp predictable trigger can transform an average gun into a tack shooter. |
|
05-13-2018, 09:52 AM | #74 | |
The Ocean is Calling
Join Date: Mar 2011
Location: Jupiter, FL
Posts: 349
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
|
|
05-13-2018, 06:42 PM | #75 | |
Freediving is Life!!
Join Date: Aug 2010
Location: Palm Beach County, FL
Posts: 237
|
Re: Double Roller Trigger for Pathos handle, Ermes Sub
Quote:
Sent from my SM-G960U using Tapatalk Last edited by Renejr83; 05-13-2018 at 07:08 PM. |
|
Bookmarks |
Thread Tools | |
Display Modes | Rate This Thread |
|
|