Home Tournaments Calendar Weather Merchandise Sponsors

Go Back   Spearboard.com - The World's Largest Spearfishing Diving Boating Social Media Forum > Spearfishing Gear > Non-Gun DIY Projects and Customizations

Non-Gun DIY Projects and Customizations This section is for your DIY spearfishing projects and customization other then spearguns.

Reply
 
Thread Tools Rate Thread Display Modes
Old 01-20-2019, 05:59 PM   #1
techwiz44
Registered User
 
Join Date: Aug 2005
Location: Atlanta area
Posts: 907
hot knife?

From inflatable sport boats, to sailboats, and powerboats…speargun and dive equipment travel covers, bags and more. Customization projects seem to be needed everywhere. Sailing Dodgers, Bimini covers, sunshades and more all require fabrics such as sunbrella, dacron, nylon, webbing etc. Even with an industrial sewing machine, you need a good way to cut the materials.

This is what I want to be able to do:

https://d1y6jrbzotnyjg.cloudfront.ne...2XWKZ35EOVO4XA

These hot knives seem to sell across a wide range of price points. From $85 up to $300 across varying manufacturers. But they all run off all the same “R” shaped blade that seems to function just like the tips that go on every 100W soldering gun. And there lies the question. I purchased the “R” shaped blade off eBay for $12. Will it function like the video if I managed to fit it into a typical 100watt soldering gun.

If the soldering gun works off a transformer that utilizes the concept of electrical resistance, and if I understand this correctly, current forces the thicker materials to heat up, but the thinner materials will get substantially hotter when the electrical current passes through them. I’m not an electrical engineer so I’m posing the question to others who may have that skill set. Most of the fabric cutting knife’s advertised run at 100 Watts.

If I can fit that “R” shaped blade into a 100W-140W soldering gun, do you think it will glow hot just like in the video? And if that works, I could buy a regular soldering gun and save a lot of money. The more expensive hot knives run $2-$300, the Chinese knockoffs sell between $85-$130. Yet name brands such as “Weller” soldering guns are only $40-$50 brand-new.

Informed and educational comments and suggestions are welcome.

or just pay for the special tool?
__________________
The true divide in America is between taxpayers and those who "game" the system. Everything else is a smokescreen to obscure that reality.

Protecting the US borders is LAWFULL- not racist.
Fabricating lies and passing it off as news is dishonest and corrupt and not worthy of protection.
techwiz44 is offline   Reply With Quote
Old 01-20-2019, 08:19 PM   #2
SEATUX
Registered User
 
SEATUX's Avatar
 
Join Date: Apr 2005
Location: Port Charlotte Fl
Age: 71
Posts: 2,096
Re: hot knife?

It should work, try it, what do you have to loose?
( God Hates a Coward...)
I have the actual cutter, it draws .6 amps at 125 volts, which is only 75 watts.
SEATUX is online now   Reply With Quote
Old 01-21-2019, 06:34 AM   #3
SEATUX
Registered User
 
SEATUX's Avatar
 
Join Date: Apr 2005
Location: Port Charlotte Fl
Age: 71
Posts: 2,096
Re: hot knife?

This is the brand knife I use, keep an eye on it..you might get lucky;
https://www.ebay.com/itm/HSGM-HeiBsc...QLkf:rk:1:pf:0

I have no experience with the off brands and knock offs, I'm sure some work better than others. That being said I just bought this for my knife, will see if it works as well;
https://www.ebay.com/itm/172557472695 $14.98 Free SH

You got me thinking, so I did do a little testing on my knife VS the Weller.
The Primary draws are almost identical, however My calculations show the transformer of the hot knife is a 150:1 ratio and By contrast the Weller is 268:1 ratio. ( calculated by measuring the output voltages )

So as you can see the Weller secondary is going to be putting out way more amps !
( Tho that was on the High switch, I didn't measure the Low switch)


BTW
Your right, mine should be drawing more like 100 watts instead of the 75 watts that it does, that's probably due to the bad/broken tip I have in it, thus the new tip being purchased)

Last edited by SEATUX; 01-21-2019 at 06:44 AM.
SEATUX is online now   Reply With Quote
Old 02-10-2019, 12:53 PM   #4
popgun pete
Registered User
 
popgun pete's Avatar
 
Join Date: Mar 2006
Posts: 2,313
Re: hot knife?

I have used a Rillfit hot knife for cutting tire treads, it was a pretty heavy duty item and they may make one for your purpose with a different shape blade in the clamps.
popgun pete is online now   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:37 AM.


The World's Largest Spearfishing Diving Social Media Forum Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Copyright ©2002 - 2014 Spearboard.com